Products

Amprobe ST-102B Data Sheet INCLUDES: • ST-102B Receptacle Tester with GFCI FEATURES: • Test GFCI breakers for proper wiring and operation • Easy to read light indicators show common wiring problems • Confirm GFCI socket is wired for protection • GFCI circuit trips to confirm tester is working • For use on 110-125 V ac SPECIFICATIONS: • Rated Operating Voltage: 110 – 125 V AC • Wattage: 0.3 W • Actuator: Black button • Indicator Lamps: Red LED, three lights, incandescent • Lamp Lens Colors: One red, two amber • Light Colors: Open ground, open neutral, open hot, hot/ground reverse, hot/neutral reverse, correct • Safety Agency Approvals: UL and cULus • Warranty: 90 Days The Amprobe ST-102B socket tester with GFCI is an outlet tester used to confirm the proper wiring of US and Canadian standard electrical outlets/sockets/receptacles and those wired with ground fault circuit interrupter (GFCI) in residential & industrial settings. Three incandescent lights and one LED indicate whether an outlet is correctly wired or the presence of five different wiring faults [open ground, open neutral, open hot, hot/ground reverse, and hot/neutral reverse]. The tester is designed to test 110 to 125V AC outlets (standard wall outlets) and is UL and Canadian UL listed for safety. properly wired. If properly wired, push the button on the top of the socket tester. EASY-TO-USE: Easily check and confirm proper wiring of electrical receptacles with the Amprobe ST-102B Receptacle Testers. Quickly confirm that GFCI breakers are properly wired for protection. NEW FEATURE: The ST-102B features a trip test function to confirm that GFCI protection is working properly (ST-102B only). WHAT’S A GFCI OUTLET?: Ground fault circuit interrupter (GFCI) outlets are there to protect people from electrical shock, typically used in areas where water is present (bathrooms and kitchens). Normal 120-volt outlets in the United States have two vertical slots and then a round hole centered below them ('ground').

Amprobe VP-1000SB Data Sheet INCLUDES: • (1) VP-1000SB Non-Contact Voltage Probe • (2) AAA Batteries (installed) • (1) Instruction Sheet FEATURES: • Provides non-contact ac voltage detection from 90V AC to 1000V AC with a CAT IV 1000 V safety rating • Tests for AC voltage in cables, circuit breakers, wall sockets, junction boxes, fuses, and more, without requiring disconnection of the electrical system • Issues simultaneous audible, visual, and shaker alerts when voltage is detected • Features a fully insulated probe, with no exposed metal or conductive parts • Safety rated for indoor and outdoor applications • Includes users manual and batteries (installed) SPECIFICATIONS: • Operating Voltage Range: 90 V AV - 1000 V AC • Sensitivity: Lights, beeps and vibrates at approximately 0.39 in (10 mm) distance from a wire carrying 120 V AC • Operating Temperature: 32 °F to 104 °F (0 °C to 40 °C), ≤ 80% RH • Storage Condition: 14 °F to 122 °F (-10 °C to 50 °C), ≤ 95% RH • Operating Altitude: 2000 meters • Power Supply: Two 1.5 V AAA batteries (installed) • Dimensions (L x W x H): 6.10 x 0.96 x 0.85 in (155 x 24.5 x 21.5 mm) • Weight: Approximately 0.11 lb (50 g) with batteries installed • Safety Compliance: IEC 61010-1 3rd Ed., UL61010-1 2nd Ed. and CAN/CSA C22.2 No. 61010.1-0.92 to CAT IV 1000 V, Pollution degree 2 , IP40 • EMC Compliance: IEC 61326-1 The Amprobe VP-1000SB Non-Contact Voltage Probe with shaker and beeper provides maximum safety and convenience for detecting AC voltage without interrupting electrical systems. Designed to conveniently fit in your shirt pocket, the VP-1000SB looks like a voltage detector pen; yet it performs in the toughest indoor and outdoor applications, operating as ‘always on’ with no buttons to push. The VP-1000SB provides visual, audible, and shaker alerts when greater than 90 V AC voltage is present, which allows the user to discern between hot and neutral wires in conventional outlets. Voltage probes with sensitivity levels set below 90 V often do not allow the user to distinguish between hot and neutral wires. QUALITY AND SAFETY, YOU CAN TRUST: The Amprobe VP-1000SB Non-Contact Voltage Probe with vibration is pocket-sized and easy to use. It is designed for safe and convenient, non-contact ac voltage detection without interruption to electrical systems. DESIGNED WITH YOU IN MIND: Test for ac voltage including in cables, circuit breakers, wall sockets, junction boxes, and fuses. The VP-1000SB provides 3-way visual, audible and vibration alerts when ac voltage is present. EASY TO USE: ALWAYS ON & NO BUTTONS: Designed to conveniently fit in your shirt pocket and to perform in the toughest indoor and outdoor applications, the VP-1000SB operates as ‘always on’ with no buttons. The VP-1000SB’s tip is designed to fit into outlets, allowing you to discern between hot and neutral wires and verify proper outlet wiring.

INCLUDES: • AM-570 Digital Multimeter • Test Leads • (2) Type-K Probe • Temperature Adapter • 9V Battery (installed) • Velcro Strap • Carrying Case • User Manual FEATURES: • True-RMS technology improves accuracy in electrically noisy environments • Measures AC/DC Voltage up to 1000V, AC/DC current, resistance, frequency, capacitance, temperature, and duty cycle • Low Z mode detects stray voltages • Low pass filter accurately measures voltage on variable frequency drives • Peak hold (crest) captures and holds the peak value of a voltage or current surge • Non-contact voltage detection enhances safety • Audible continuity quickly identifies shorts and opens • Diode test to verify diode polarity • Data hold freezes the reading on the display for further analysis • MIN/MAX recording records min/max measurements over time to show voltage fluctuations • Relative zero mode displays the difference between the actual reading and a stored reference value and may be used with any function or range • Warning alerts against improper test leads connection • Combines user friendly features such as, auto power-off to conserve battery life, low battery warning, a “third hand test probe holder, built-in test leads storage, a built-in flashlight, and a Velcro strap to hang the meter • Dual reading backlit LCD display with analog bar graph makes it easy to view results SPECIFICATIONS: • True-rms: Yes • AC Voltage: 6.000 V, 60.00 V, 600.0 V, 1000 V • DC Voltage: 600.0 mV, 6.000 V, 60.00 V, 600.0 V, 1000 V • AC Current: 600.0 ?A, 6000 ?A, 60.00 mA, 500.0 mA, 10.00 A • DC Current: 600.0 ?A, 6000 ?A, 60.00 mA, 500.0 mA, 10.00 A • Frequency: 60.00 Hz, 600.0 Hz, 6.000 kHz, 60.00 kHz, 600.0 kHz, 6.000 MHz, 60.00 MHz • Resistance: 600.0 ?, 6.000 k?, 60.00 k?, 600.0 k? 6.000 M? 60.00 M? • Capacitance: 60.00 nF, 600.0 nF, 6.000 ?F, 60.00 ?F, 600.0 ?F, 6000 ?F, 60.00 mF • Temperature: -40 ?F to 1832 ?F, -40 ?C to 1000 ?C • Number of temperature inputs: Dual Thermocouple • Duty cycle: 10.00% to 90.00% The Amprobe AM-570 is the best multimeter in its class designed for professional electricians and HVAC technicians who need to maintain, service or troubleshoot advanced electrical systems in the most demanding environments. Packed full of features such as True RMS, dual thermocouples for taking differential temperature measurements, a low impedance function to detect stray voltage, and a low pass filter to accurately take measurements on variable frequency drives, the Amprobe AM-570 Digital Multimeter allows for quick go/no-go checks without the need for an additional tool. Multimeters are indispensable electrical test meters that measure multiple properties of an electrical circuit, such as current, voltage, resistance, capacitance, and continuity. The AM-570 can be used to diagnose electrical problems in electrical equipment, wiring, and power supplies. With the included temperature thermocouples and test leads, this multimeter can be connected to a circuit or device to measure its electrical or performance properties to confirm functionality. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. This multimeter has been designed for use in industrial environments to test voltages up to 1000V and 10A. This meter is rated Category IV/600V, Category III/1000V. Safety ratings are based on International Electrotechnical Commission (IEC) standards for low-voltage test equipment. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating. PACKED WITH FEATURES: The Amprobe AM-570 Industrial Digital Multimeter with True RMS is a digital multimeter that measures AC/DC voltage to 1,000V, AC/DC current to 10A, frequency to 60 MHz, resistance to 60 megaohms, capacitance to 60 millifarads, and temperature from -40 to +1832 degrees F (-40 to +1000 degrees C). It also performs audible continuity tests and diode tests. WHAT IS TRUE-RMS METER?: True RMS (root mean square) meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has an undistorted waveform, or nonlinear loads, such as electronic devices or motors, where the current or voltage has a distorted waveform. NON-CONTACT VOLTAGE DETECTION ENHANCES SAFETY: The AM-570 features a built-in flashlight to see wires and fuses in the dark, a rubber tilt stand and probe holder to give you the 'third-hand' you need while taking measurements.

INCLUDES: • AT-7000-R Reciever • AT-7000-T Transmitter • TL-7000 Test Leads • CC-7000 Hard Carrying Case • SC-7000 Signal Clamp • HS-1 Hanger • Battery Charger (3) • Rechargeable AA Batteries (10) • User Manual FEATURES: • Locates and traces energized and de-energized wires and breakers in floors, walls, and ceilings • Pinpoints shorts and opens • Traces AC/DC Circuits from 0-600 V • Features three power modes: "High" power mode for normal circuits, "Low" power mode for precision tracing in difficult areas and Clamp power mode provides a boosted induction signal via the optional signal clamp • Offers two output frequency modes for optimal tracing: 6 kHz for energized circuits and 33 kHz for de-energized circuits • Provides embedded help screens to simplify setup • Includes Signal Clamp (SC-7000) clamp-on attachment for inducing a signal in wires where you don’t have access to bare conductors • Comes with custom Amprobe hard carrying case, test leads, and accessories • Connects to optional TIC 410A Hot Stick attachment to make it easier to trace wires in high ceilings, walls, and along floors SPECIFICATIONS: • Traces energized and de-energized wires • Locates energized and de-energized breakers • Pinpoints opens and shorts • Traces AC/DC circuits 0-600 V • Three power modes • Two frequency modes for optimal tracing Get accurate results in minutes with great features and technologies that simplify wire tracing and breaker identification. The Receiver’s patented Smart Sensor, with its great antenna design and advanced signal processor, clearly displays the location and orientation of energized wires in walls, floors and ceilings on the large color TFT LCD screen. The powerful Transmitter utilizes two optimal frequencies for both energized and de-energized wire and breaker tracing, delivering consistently accurate results for novice users and experts alike. The new Scan and Locate feature clearly identifies the one correct breaker or fuse, eliminating the confusion from multiple false positive readings common in older technology tracing tools. TRACE WIRES INSIDE CONDUIT: Trace energized and e-energized wires enclosed in metal conduit by removing the junction box cover and using the AT-7000-R Receiver’s Tip Sensor to identify the specific wire carrying the transmitted signal generated by the AT-7000-T Transmitter. Wires in non-metal conduit can be traced directly without opening the junction box and using the AT-7000-R Receiver’s Smart Sensor. USE THE TIP SENSOR TO TRACE WIRES IN HARD TO REACH AREAS: When used with the AT-7000-T Transmitter, the Tip Sensor pinpoints the location of energized and de-energized wires in tight, hard to reach spaces. It easily and accurately traces the targeted energized and de-energized wires in junction boxes, corners, walls, floors and ceilings to a depth of up to 20 feet. NON-CONTACT VOLTAGE (NCV) DETECTION: The NCV feature extends functionality of the AT-7000-R receiver by detecting energized wires from 90 to 600 V and 40 to 400 Hz without the use of the AT- 7000-T Transmitter. Its adjustable sensitivity fits a range of applications, from detecting presence of voltage (higher sensitivity) to precisely pinpointing a hot wire in a bundle (lower sensitivity). TRACE WIRES WITHOUT ACCESS TO EXPOSED CONDUCTORS: The SC-7000 signal clamp accessory can be used with the AT-7000-T Transmitter to induce a signal into energized and de-energized wires when there is no access to bare conductors. Simply clamp around the desired wire to induce the signal, then begin tracing.

INCLUDES: • PRM-6 Phase Sequence and Motor Rotation Tester • Test Probes (3) • Alligator Clips (3) • Carrying Bag • 2 x AAA Batteries (Installled) • User Manual FEATURES: • 3-phase wire sequence indication • Error displays (missing phase, one input connected to neutral or PE) • Non-contact, wireless motor rotation detection on running motors • Indicates motor rotation of disconnected motors when spinning the shaft by hand or other means • 3-phase to phase voltage up to 700 V • Clear backlit LCD display • Durable rubber casing for 3 ft. (1 m) drop proof protection • Safety: CAT IV 600 V SPECIFICATIONS: • Operating temperature: 0°C to 40°C (32°F to 104°C) • Operating altitude: Up to 2000 m • Power: AAA battery (2) • 3 phase indication: LCD • Dimensions: (H x W x D) 5.43 in x 2.56 in x 1.3 in (13.7 cm x 6.5 cm x 3.3 cm) • Weight: .38 lb (.17 kg) including battery • Dust/water resistance: IP 40 • Pollution degree: 2 • Overvoltage category: CAT IV 600 V • Agency approvals: CE, cCSAus • Safety: Conforms to EN 61010-1, EN 61010-031, EN 61557-1, EN 61557-7 • EMC: Conforms to EN 61326-1 Professionals who install or maintain 3-phase motors or systems recognize how crucial it is to verify the correct motor rotation and wiring phase sequence. Improper connections can cause motors to rotate in reverse direction, potentially damaging the motor and the equipment it’s powering. The PRM-6 Phase Sequence and Motor Rotation Tester is easy-to-use and reliable to test the motor rotation of 3-phase systems with traditional test leads. In addition, it can verify 3-phase receptacle wiring and phase sequencing. Durably constructed with a rubber outer casing, the PRM-6 has a bright backlight LCD display, CAT IV 600-volt rating, and conforms to EN 61010 and EN 61557 standards making it an essential tool for motor rotation and phase sequence testing in commercial and industrial environments on electrical systems up to 700 V. VERIFIES MOTOR ROTATION OF DISCONNECTED MOTORS: Indicates motor rotation in disconnected motors using test leads and by spinning the shaft by hand or other means. WIRELESS MOTOR ROTATION DETECTION ON RUNNING MOTORS: Tests for rotation direction on a running motor with the built-in non-contact, wireless sensor – specifically important for fast running motors or motors where the shaft is not visible. PHASE ROTATION IN 3-PHASE SYSTEMS: Indicates the phase rotation. 3-phase systems for both power sources and motors, as well as identifies faulty 3-phase wiring with de-energized phases or incorrectly wired receptacles.

Amprobe PK-110 Data Sheet INCLUDES: • AM-420 Multimeter with 9V alkaline battery (installed), User manual • VP-1000 Non-Contact Voltage Probe with (2) 1.5 V AAA batteries (installed), User manual • ST102B Socket Tester with GFCI, User Manual FEATURES: • Kit contains tools to measure voltage up to 300 V AC/DC, AC/DC current and resistance, capacitance and perform battery tests • RV Safety Testing: check RV pedestal outlets (20 A, 30 A, 50 A) for proper wiring and grounding, check for “hot skin conditions and proper wiring of outlets in your RV • Check for presence of voltage in receptacles, switches, extension cords and light fixtures • Verify proper wiring of GFCI (ground fault circuit interrupter) and standard US and Canadian wall outlets with a simple push of a button • UL and CSA listed for safety SPECIFICATIONS: • AM-420: AC voltage 200.0 / 250 V • AM-420: DC voltage 200 mV 2.000 / 20.00 / 200.0 / 250 V • AM-420: DC current 200.0 μA 2.000 / 20.00 / 200.0 mA • AM-420: Resistance 200.0 Ω 2.000 / 20.00 / 200.0 kΩ 2.000 MΩ • AM-420: Continuity Beeps at ≤10 Ω, off at >70 Ω • VP-1000: Operating voltage range 90 Vac → 1000 Vac, 50/60 Hz • VP-1000: Sensitivity Lights at approx. 10 mm (0.39 in) distance from a wire carrying 120 Vac • VP-1000: Storage condition -10°C to +50°C (14°F to 122°F), ≤ 95% RH • VP-1000: Operating altitude 2000 meters • ST-102B: Operating Voltage 110 – 125 Vac, 50 – 60 Hz • ST-102B: Wattage 0.3 W • ST-102B: Actuator Black button • ST-102B: Indicator Red LED, three lights, neon • ST-102B: Lamp Lens Colors One red, two amber Amprobe’s PK-110 Electrical Test Kit offers three electrical testers with testing functions suitable for a variety of residential applications. The kit includes the AM-420 Digital Multimeter, ST-102B Socket Tester with GFCI and VP-1000 Non-Contact Voltage Detector. From identifying voltage presence in outlets and switches to confirming proper wiring of regular and GFCI protected outlets, the PK-110 kit boasts all the features needed to perform quick and safe electrical tests. AM-420 DIGITAL MULTIMETER: Accurately measure voltage up to 250V in receptacles, switches, extension cords and light fixtures. Troubleshoot light bulbs and fuses with the continuity function. Check 1.5V and 9V batteries. Test extension cords and verify proper wiring of an outlet with voltage function. CAT II 250 V safety rating. VP-1000 NON-CONTACT VOLTAGE DETECTOR: Easily and safely detect voltage presence between 90 and 1000 V. Quickly verify voltage presence in outlets, switches, extension cords, circuit breakers and fuses without disconnecting the electrical system. Bright LED alerts when voltage is present. Operates as ‘always on’ using low power circuitry with no buttons for increased safety. Double insulated, CAT IV 1000V safety rating. ST-102B SOCKET TESTER WITH GFCI: Test receptacle wiring and confirm GFCI sockets are properly wired with push button. Detect five different wiring faults open ground, open neutral, open hot, hot/ground reverse, and hot/neutral reverse. Three illuminated lights on the tester indicate the type of wiring problem.

INCLUDES: • Amprobe AT-2004-A Advanced Wire Tracer • R-2000 Receiver • S-2600-A Transmitter 9-300V • T-2200 Transmitter for Open Tracing • A-2201CE Clamp-On Attachment • C2901 Cordset 110 Volt Plug to Banana Plugs • C2902 Cordset Alligator Clips to Banana Plugs FEATURES: • Detects and traces wires buried in walls and floors, up to 13 feet (4m) deep, as well as in plastic conduit, cable shield and computer cables • Traces energized wires and locates breakers without interrupting power • Traces de-energized wires (continuity and grounded wire) and pinpoints shorts and ground faults • Traces de-energized open (broken or disconnected) wires and locates the point where the wire is broken • Includes a clamp-on attachment for injecting a signal into wires when bare wire access isn't available • Does not interfere with sensitive electronic equipment, such as in hospitals and data centers SPECIFICATIONS: • Traces energized wires without power interruption: 9-300V (S2600-A Transmitter) • Locates breakers without power interruption: 9-300V (S2600-A Transmitter) • Traces unenergized wires (wire continuity and wire grounded at the end): S2600-A Transmitter and 9V batteries • Pinpoints place where wire is broken: T2200 Transmitter • Supplied with clamp-on attachment to inject signal without making a contact with bare wire: Yes The Amprobe AT-2004-A Advanced Wire Tracer is a circuit tracer that locates and traces energized and de-energized wires, breakers, neutrals, and grounds to identify shorts, ground faults, and broken wires. It detects and traces wires in walls, floors, conduit, and computer cables and does not interfere with sensitive electronic equipment. This makes it safe to use in hospitals and data centers. HOW IT WORKS : Connect the transmitter (T-2200 for de-energized lines or S-2600-A for energized circuits) to generate a signal, which is traceable by the R-2000 receiver. For tracing wires, the receiver will pick up the signal along the path of the wire allowing the user to trace the path of the wire behind ceilings, walls and floors. For opens and shorts (where wires are shorted or broken), the signal will break or stop as you are tracing along the wire indicating the location of the fault. For locating breakers, scan the breaker panel for the highest signal level indicating the breaker that is connected to the transmitter. Use the signal clamp accessory for applications where there is no access to bare conductors, the signal can be induced through the insulation of the wire using the clamp attachment (A-2201CE). ADDITONAL PRODUCT INFORMATION : The tracer includes the R-2000 receiver, which works with one of two transmitters. The T-2200 transmitter traces wire continuity and wire grounds on de-energized systems, while the S-2600 transmitter is compatible with energized 9 to 300 V alternating current (AC) or direct current (DC). The receiver can trace energized wires buried or hidden behind walls up to 13 feet deep. The AT-2004-A is designed for use by electricians and electrical contractors.

INCLUDES: • Amprobe AT-2005-A Advanced Wire Tracer • R-2000 Receiver • S-2600-A Transmitter 9-300V • T-2200 Transmitter for Open Tracing • Clamp-On Transmitter • C2901 Cordset 110 Volt Plug to Banana Plugs • C2902 Cordset Alligator Clips to Banana Plugs • Users Manual FEATURES: • Detects and traces wires buried in walls and floors, up to 13 feet (4m) deep, as well as in plastic conduit, cable shields and computer cables • Traces energized wires and locates breakers without interrupting power • Traces de-energized wires and pinpoints shorts, opens, and ground faults • Comes with a battery booster to strengthen the signal for more accurate open tracing • Includes a clamp-on attachment for injecting a signal where access to bare wires is not available • Does not interfere with sensitive electronic equipment, such as in hospitals and data centers SPECIFICATIONS: • Traces energized wires without power interruption: 9-300V (S2600-A Transmitter) • Locates breakers without power interruption: 9-300V (S2600-A Transmitter) • Traces unenergized wires (wire continuity and wire grounded at the end): S2600-A Transmitter and 9V batteries • Pinpoints place where wire is broken: T2200 Transmitter • Traces unenergized open wires (broken or disconnected wire): T2200 Transmitter • Pinpoints place where wire is broken: T2200 Transmitter • Supplied with battery booster to strengthen signal for open tracing: Yes • Supplied with clamp-on attachment to inject signal without making a contact with bare wire : Yes The Amprobe AT-2005-A advanced wire tracer is a circuit tracer that locates and traces energized and de-energized wires, breakers, neutrals, and grounds to identify shorts, ground faults, and broken wires. It locates and traces wires in walls, floors, conduit, and computer cables and does not interfere with sensitive electronic equipment. This makes it safe to use in hospitals and data centers. The AT-2005-A includes the rechargeable booster battery pack with recharger that amplifies the signal for improved de-energized wire tracing. This is the only difference between the AT-2004-A and AT-2005-A. HOW IT WORKS: Connect the transmitter (T-2200 for de-energized lines or S-2600-A for energized circuits) to generate a signal, which is traceable by the R-2000 receiver. For tracing wires, the receiver will pick up the signal along the path of the wire and allow the user to trace the path of the wire behind ceilings, walls and floors. For opens and shorts (where wires are shorted or broken), the signal will break or stop as the user is tracing along the wire, indicating the location of the fault. For locating breakers, scan the breaker panel for the highest signal level indicating the breaker that is connected to the transmitter. Where there is no access to bare conductors, the signal can be induced through the insulation of the wire using the clamp attachment (A-2201CE). ADDITIONAL PRODUCT INFORMATION: The kit includes an R-2000 receiver that can work with one of two transmitters. The T-2200 transmitter traces wire continuity and wire grounds on de-energized systems, while the S-2600 transmitter is compatible with energized 9 to 300V alternating current (AC) or direct current (DC). An included clamp-on transmitter accessory injects a signal for non-contact operation. The receiver can trace energized wires buried or hidden behind walls up to 13 feet deep. The AT-2005-A is designed for use by electricians and electrical contractors.

INCLUDES: • Receiver • Transmitter • Connection Cables • Carrying Case • Users Manual FEATURES: • Operates at 6 kHZ for more accurate readings on energized lines • Locates and traces energized wires in walls, floors, conduit, and computer cables, without interrupting power • 12 sensitivity settings for reliable wire tracing • Traces energized wires hidden behind walls up to 13ft. Deep • Pinpoints shorts, breakers, neutrals, broken wires and grounds • Comes equipped with a digital filter to assure accuracy in noisy environments • Does not interfere with sensitive electronic equipment SPECIFICATIONS: • Traces energized wires without power interruption. Locates breakers without power interruptio 9 V ? 300 V AC/DC 300 ? 300 V AC • Traces unenergized wires (wire continuity and wire grounded at the end). Pinpoints shorts and ground faults: Transmitter & 9V batteries • Digital filter to assure cutting edge accuracy in noisy industrial environments: Yes • Sensitivity settings: 12 The Amprobe CT-326-C current tracer is a circuit tracer for locating and tracing electrical wires, breakers, neutrals, and ground lines in industrial settings. Twelve sensitivity settings allow the tracer to identify shorts and ground faults on both electrified and non-electrified circuits. LED lights indicate the presence of wires and breakers. The unit traces live wires and circuit breakers from 9 to 300V AC and 9 to 300V DC. The tracer digitally filters out electrical noise for increased accuracy in industrial settings. The unit locates and traces live wires and breakers buried underground or hidden in walls up to 13 feet deep without interrupting power. The tracer is powered by one 9V battery (installed), which provides power for about 100 hours of testing. It is shielded, so it does not interfere with sensitive equipment. The CT-326-C is designed to trace energized and non-energized wires and circuit breakers by electricians and electrical contractors in industrial settings. PACKED WITH FEATURES: The CT-326-C wire tracing tool quickly pinpoints energized wires hidden in walls, ceilings and floors up to 13’ deep without having to interrupt power. LOCATES AND TRACES WIRES: The CT-326-C is a heavy duty product recommended for tough industrial applications. The CT-326-C locates and traces energized and unenergized wires in walls, floors, conduit, and computer cables. PRECISE ACCURACY: This electrical wire tracer is equipped with a digital filter to assure precise accuracy even in noisy environments.

INCLUDES: • Amprobe AMP-210 Clamp Meter • Test Leads • 2 x AAA Batteries (installed) • User Manual • Carrying Case FEATURES: • Measures AC Current to 600 A and AC/DC Voltage to 600 V • Features True-RMS sensing for accurate voltage measurements in noisy electrical environments • Amp-Tip delivers precise low AC current measurements – 0 to 60 A • Includes a low pass filter to accurately measure voltage and current on variable frequency drives • Capacitance measurement, continuity beeper and diode test • Provides resistance and continuity measurement capabilities to verify the quality of electrical connections and the proper operation of motor and transformer coils • Offers data hold and relative zero for quick analysis • Maximizes battery life with auto power off and low battery indicator • Backlit display for easy measurement viewing in bright and dim environments • Accommodates conductors up to 1.18 in (30mm) SPECIFICATIONS: • AC voltage (True-rms) Range: 0 to 600.0 V • DC voltage Range: 0 to 600.0 V • AC current Range: 0 to 600.0 A • Precise low current AC Range: 0 to 60.00 A • Frequency Range: 5.00 to 999.9 Hz • Resistance Range: 0.0 to 60.00 k? • Capacitance Range: 0.0 to 2500 µF • Continuity beeper: ON ? 10 ?, Off > 250 ? • Non-contact voltage: 10 V to 1000 V AC (50 to 60 Hz) • Diode test: Yes • Jaw opening: 1.18 in (30 mm) • Safty rating: CAT III 600 V Amprobe’s AMP-210 600 A TRMS Clamp Meter offers a complete range of measuring functions for today’s modern electrical environments. Features include True-RMS sensing, low pass filters and fast response processors for quick, error-free measurements. The Amp-Tip function allows for precise measurement of current down to the tenth of an Amp, enabling accurate current measurement of both large and small diameter wires. GET ACCURATE MEASUREMENTS: The Amprobe AMP-210 provides accurate measurement of current, voltage and frequency on all electrical systems including distorted, non-sinusoidal signals (True-RMS function) and variable frequency drives (low-pass filter). AMP-TIP FUNCTION: The Amp-Tip function can be used for precise low current measurement of small diameter wires down to 0.1 Amp to help with electrical system troubleshooting. ROTATION DETECTION: Low pass filter allows measurement of current and voltage on variable frequency drives (motors with speed controlled by frequency). Without this feature, the meter would provide erroneous readings when measuring voltage and current.

INCLUDES: • Amprobe AMP-220 Clamp Meter • Test Leads • 2 x AAA Batteries (installed) • User Manual • Carrying Case FEATURES: • Measures AC Current to 600 A and AC/DC Voltage to 600 V • Features True-RMS sensing for accurate voltage measurements in noisy electrical environments • Amp-Tip delivers precise low AC current measurements – 0 to 60 A • Includes a low pass filter to accurately measure voltage and current on variable frequency drives • Capacitance measurement, continuity beeper and diode test • Provides resistance and continuity measurement capabilities to verify the quality of electrical connections and the proper operation of motor and transformer coils • Offers data hold and relative zero for quick analysis • Maximizes battery life with auto power off and low battery indicator • Backlit display for easy measurement viewing in bright and dim environments • Accommodates conductors up to 1.37 in (35mm) SPECIFICATIONS: • AC voltage (True-rms) Range: 0 to 600.0 V • DC voltage Range: 0 to 600.0 V • AC+DC voltage Range: 0 to 600.0 V • AC current Range: 0 to 600.0 A • DC current Range: 0 to 600.0 A • AC+DC current Range: 0 to 600.0 A • Precise low current AC Range: 0 to 60.00 A • Precise low current DC Range: 0 to 60.0 A • Frequency Range: 5.00 to 999.9 Hz • Resistance Range: 0.0 to 60.00 k? • Capacitance Range: 0.0 to 2500 µF • Continuity beeper: ON ? 10 ?, Off > 250 ? • Diode test: Yes • Jaw opening: 1.37 in (35 mm) • Safty rating: CAT III 600 V Amprobe’s AMP-220 600 A TRMS Clamp Meter offers a complete range of measuring functions for today’s modern electrical environments. Features include True-RMS sensing, low pass filters and fast response processors for quick, error-free measurements. The Amp-Tip function allows for precise measurement of current down to the tenth of an Amp, enabling accurate current measurement of both large and small diameter wires. GET ACCURATE MEASUREMENTS: The Amprobe AMP-220 provides accurate measurement of current, voltage and frequency on all electrical systems including distorted, non-sinusoidal signals (True-RMS function) and variable frequency drives (low-pass filter). AMP-TIP FUNCTION: The Amp-Tip function can be used for precise low current measurement of small diameter wires down to 0.1 Amp to help with electrical system troubleshooting. ROTATION DETECTION: Low pass filter allows measurement of current and voltage on variable frequency drives (motors with speed controlled by frequency). Without this feature, the meter would provide erroneous readings when measuring voltage and current.

INCLUDES: • Amprobe AMP-310 Clamp Meter • Banana Plug Type-K Thermocouple • Test Leads • 2 x AAA Batteries (installed) • User Manual • Carrying Case FEATURES: • Measures AC Current to 600 A and AC/DC Voltage to 600 V • Measures temperature from -40° to 752°F, (-40° to 400°C) • Measures DC Microamps output to test proper operation of the flame sensor on gas appliances • Measures capacitance, test diodes, and features a continuity beeper • Tests 3-phase sequence and motor rotation to ensure proper connection of a motor to a 3-phase system • Monitors inrush current during motor start-up • Features True-RMS sensing for accurate voltage measurements in noisy electrical environments • Amp-Tip function delivers precise low AC current measurements – 0 to 60 A • Includes a low pass filter to accurately measure voltage and current on variable frequency drives • Provides resistance and continuity measurement capabilities to verify the quality of electrical connections and the proper operation of motor and transformer coils • Provides data hold, relative zero, and MAX/MIN/AVG mode for quick analysis • Maximizes battery life with auto power off and low battery indicator • Backlit display for easy measurement viewing in bright and dim environments SPECIFICATIONS: • AC voltage (True-rms) Range: 0 to 600.0 V • DC voltage Range: 0 to 600.0 V • AC current Range: 0 to 600.0 A • Precise low current AC Range: 0 to 60.00 A • Micro amps Range: 0 to 2000 µA • Frequency Range: 5.00 to 999.9 Hz • Resistance Range: 0.0 to 60.00 k? • Continuity beeper: ON ? 10 ?, Off > 250 ? • Temperature (Type K thermocouple): -40.0 to 752 °F, -40.0 to 400 °C • Non-contact voltage: 10 V to 1000 V AC (50 to 60 Hz) • Phase rotation indication: Rotation-R for main supply, Rotation-M for motors • Diode test: Yes • Jaw opening: 1.18 in (30 mm) • Safty rating: CAT III 600 V Amprobe’s AMP-310 True-RMS Clamp Meter offers a complete range of measuring functions for modern industrial environments, motor testing and HVAC applications. The AMP-310 features True-RMS sensing, low pass filters and fast response processors for quick, error-free measurements. The Amp-Tip function allows for precise measurement of current down to the tenth of an Amp, and a third input jack enables motor rotation and 3-phase sequence testing. GET ACCURATE MEASUREMENTS: The Amprobe AMP-310 provides accurate measurement of current, voltage and frequency on all electrical systems including distorted, non-sinusoidal signals (True-RMS function) and variable frequency drives (low-pass filter). 3-PHASE MOTOR AND PHASE ROTATION: Tests allow proper connection of a motor to a 3-phase system. Improperly connected motors will spin in a reverse direction, which may destroy the motor or equipment connected to it. INDUSTRIAL MOTOR MAINTENANCE: Inrush current measurement for motor start-up monitoring allows users to verify that the motor is receiving the required inrush current to support proper motor start.

INCLUDES: • Amprobe AMP-320 Clamp Meter • Banana Plug Type-K Thermocouple • Test Leads • Alligator Clip Set • 2 x AAA Batteries (installed) • User Manual • Carrying Case FEATURES: • Measures AC/DC Current to 600 A and AC/DC Voltage to 600 V • Measures temperature from -40° to 752°F, (-40° to 400°C) • Measures DC Microamps output to test proper operation of the flame sensor on gas appliances • Measures capacitance, test diodes, and features a continuity beeper • Tests 3-phase sequence and motor rotation to ensure proper connection of a motor to a 3-phase system • Monitors inrush current during motor start-up • Features True-RMS sensing for accurate voltage measurements in noisy electrical environments • Amp-Tip function delivers precise low AC current measurements – 0 to 60 A • Includes a low pass filter to accurately measure voltage and current on variable frequency drives • Provides resistance and continuity measurement capabilities to verify the quality of electrical connections and the proper operation of motor and transformer coils • Provides data hold, relative zero, and MAX/MIN/AVG mode for quick analysis • Maximizes battery life with auto power off and low battery indicator • Backlit display for easy measurement viewing in bright and dim environments SPECIFICATIONS: • AC voltage (True-rms) Range: 0 to 600.0 V • DC voltage Range: 0 to 600.0 V • AC+DC voltage Range: 0 to 600.0 V • AC current Range: 0 to 600.0 A • DC current Range: 0 to 600.0 A • AC+DC current Range: 0 to 600.0 A • Precise low current AC Range: 0 to 60.00 A • Micro amps Range: 0 to 2000 µA • Frequency Range: 5.00 to 999.9 Hz • Resistance Range: 0.0 to 60.00 k? • Capacitance Range: 0.0 to 2500 µF • Continuity beeper: ON ? 10 ?, Off > 250 ? • Temperature (Type K thermocouple): -40.0 to 752 °F, -40.0 to 400 °C • Non-contact voltage: 10 V to 1000 V AC (50 to 60 Hz) • Phase rotation indication: Rotation-R for main supply, Rotation-M for motors • Diode test: Yes • Jaw opening: 1.37 in (35 mm) • Safty rating: CAT III 600 V Amprobe’s AMP-320 True-RMS Clamp Meter offers a complete range of measuring functions for modern industrial environments, motor testing and HVAC applications. The AMP-320 features True-RMS sensing, low pass filters and fast response processors for quick, error-free measurements. The Amp-Tip function allows for precise measurement of current down to the tenth of an Amp, and a third input jack enables motor rotation and 3-phase sequence testing. GET ACCURATE MEASUREMENTS: The Amprobe AMP-320 provides accurate measurement of current, voltage and frequency on all electrical systems including distorted, non-sinusoidal signals (True-RMS function) and variable frequency drives (low-pass filter). 3-PHASE MOTOR AND PHASE ROTATION: Tests allow proper connection of a motor to a 3-phase system. Improperly connected motors will spin in a reverse direction, which may destroy the motor or equipment connected to it. INDUSTRIAL MOTOR MAINTENANCE: Inrush current measurement for motor start-up monitoring allows users to verify that the motor is receiving the required inrush current to support proper motor start.

INCLUDES: • Amprobe AMP-330 Clamp Meter • Banana Plug Type-K Thermocouple • Test Leads • Alligator Clip Set • 2 x AA Batteries (installed) • User Manual • Carrying Case FEATURES: • Measures AC/DC Current to 1000 A and AC/DC Voltage to 1000 V • Measures temperature from -40° to 752°F, (-40° to 400°C) • Measures DC Microamps output to test proper operation of the flame sensor on gas appliances • Measures capacitance, test diodes, and features a continuity beeper • Tests 3-phase sequence and motor rotation to ensure proper connection of a motor to a 3-phase system • Monitors inrush current during motor start-up • Features True-RMS sensing for accurate voltage measurements in noisy electrical environments • Amp-Tip function delivers precise low AC current measurements – 0 to 60 A • Includes a low pass filter to accurately measure voltage and current on variable frequency drives • Provides resistance and continuity measurement capabilities to verify the quality of electrical connections and the proper operation of motor and transformer coils • Provides data hold, relative zero, and MAX/MIN/AVG mode for quick analysis • Maximizes battery life with auto power off and low battery indicator • Backlit display for easy measurement viewing in bright and dim environments • CAT IV 600 V, CAT III 1000 V safety rated • Boasts peak hold and work light • Accommodates conductors up to 2.0 inches (51mm) SPECIFICATIONS: • AC voltage (True-rms):0 to 1000.0 V • DC voltage:0 to 600.0 V • AC+DC voltage: 0 to 1000.0 V • AC current: 0 to 600.0 A • DC current: 0 to 1000.0 A • AC+DC current:0 to 1000.0 A • Precise low current AC: 0 to 60.00 A • Precise low current DC: 0 to 60.00 A • Micro amps: 0 to 2000 µa • Frequency: 5.00 to 999.9 Hz • Resistance: 0.0 to 60.00 k? • Capacitance: 0.0 to 2500 µF • Continuity beeper: ON ? 10 ? • Temperature (Type K thermocouple): -40.0 to 752 °F, -40.0 to 400 °C • Non-contact voltage:10 V to 1000 V AC (50 to 60 Hz) • Phase rotation indication: Rotation-R for main supply, Rotation-M for motors • Diode test: Yes • Jaw opening:2.0 in (51 mm) • Safety rating: CAT IV 600V, CAT III 1000 V Amprobe’s AMP-330 True-RMS Clamp Meter offers a complete range of measuring functions for modern industrial environments, motor testing and HVAC applications. The AMP-330 features True-RMS sensing, low pass filters and fast response processors for quick, error-free measurements. The Amp-Tip function allows for precise measurement of current down to the tenth of an Amp, and a third input jack enables motor rotation and 3-phase sequence testing. GET ACCURATE MEASUREMENTS: The Amprobe AMP-330 provides accurate measurement of current, voltage and frequency on all electrical systems including distorted, non-sinusoidal signals (True-RMS function) and variable frequency drives (low-pass filter). 3-PHASE MOTOR AND PHASE ROTATION: Tests allow proper connection of a motor to a 3-phase system. Improperly connected motors will spin in a reverse direction, which may destroy the motor or equipment connected to it. INDUSTRIAL MOTOR MAINTENANCE: Inrush current measurement for motor start-up monitoring allows users to verify that the motor is receiving the required inrush current to support proper motor start.

INCLUDES: • Amprobe BAT-250 Battery Tester • User's Manual FEATURES: • Quickly indicates if batteries are “good, “low or “replace" • Test standard and rechargeable batteries: 9V, AA, AAA, C, D, 1.5V button type • Ergonomic design is easy to hold • Side cradle holds batteries in place during testing • No batteries required to operate • Large, upright display is easier to read • V-shaped cradle holds batteries securely in place during testing for consistently accurate results • High-qualtity 9V Contacts • Slider is shaped for easier operation and one-handed testing • Case shape contours to your hand for easy operation SPECIFICATIONS: • I Max at F.S.D. (typical): 1.5 V: 375 mA, 9 V: 40 mA • Nominal Load (typical): 1.5 V: 4 ?, 9 V: 215 ? • Battery Size 9 V, AAA, AA, C, D and 1.5 V button/coin/watch battery • Dimensions ( L x W x H): 4.3 x 2.9 x 1.1 in (110 x 74 x 29 mm) • Weight Approximately: 0.11 lb (50 g) • Certification: CE The new BAT-250 was designed to enable one-handed battery testing. The display orientation has also been adjusted for easier reading during testing. The redesigned side cradle holds batteries securely in place during testing – no more erratic battery readings from movement off contacts. New high-quality 9V contacts make tests more straight forward and error-free. The enhanced slider shape is now more ergonomic and convenient for one-handed testing. The shape of the case has been molded to better contour to your hand for comfortable measurements. Battery failure is one of the most common causes for sensor or instrument failure. The BAT-250 Battery Tester indicates the amount of charge remaining in standard and rechargeable batteries. The analog display needle moves on a color-coded, calibrated scale to quickly identify 'good' (green), 'low' (yellow), and 'replace/recharge' (red) battery status. The BAT-250 tests 9V, AA, AAA, C, D and 1.5V Button Type batteries. Tester does not require any internal batteries to operate. ERGONOMIC DESIGN: Shape of the case contours to your hand for comfortable measurements. NEW SIDE CRADLE: Side cradle holds batteries securely in place during testing. HIGH-QUALITY 9V CONTACTS: New high-quality 9V contacts make tests more straight forward and error-free. ADJUSTED DISPLAY ORIENTATION: The display orientation has been adjusted for easier reading.

INCLUDES: • Amprobe ACD-14-PRO Digital Clamp Multimeter • Test Leads • Banana Plug K-Type • Thermocouple • Carrying Case • AAA Batteries (2) • User Manual FEATURES: • Large LCD with dual display and low-light backlight • True-rms for accurate voltage measurements in noisy environments • Low pass filter for current and voltage measurements on variable frequency drives • Amp-Tip function for precise low current measurement of small diameter wires down to 0.1 Amp to help with electrical system troubleshooting • HVAC applications with Temperature, DC Micro-amps and Capacitance • In-rush current • Non-contact voltage detection (NCV) • Audible continuity and diode test • Data hold • Auto ranging • Auto Power Offer • Low Battery indicator • Safety Rated CAT III 600 V SPECIFICATIONS: • Safety rating: CAT III 600 V • AC/DC Voltage (V): 600 • AC Current (A): 600 • Jaw Opening: 1.18 in (30 mm) • Micro Amps (µA): 2000 • Temperature: -40 °F to 752 °F / -40 °C to 400 °C • Frequency (Hz): 5.00 to 999.9 • Resistance (k?): 6000 • Capacitance (µF): 2500 • Continuity Beeper: < 10 ? The ACD-14 PLUS Digital Clamp Meter is the perfect choice for both HVAC and electrical applications due to its versatile set of features. Electricians will find it’s thin, light and versatile with thinner jaws than standard clamp meters (only 0.4”/10mm thick). Its ability to measure temperature, capacitance, and microamps are important features for HVAC technicians. The ACD-14 PLUS meter offers thinner jaws over standard clamp meters, allowing access to tight measurement areas and still accommodating conductors up to 25 mm. QUICK AND ACCURATE MEASUREMENTS: Accurate measurement of current, voltage and frequency on all electrical systems including distorted, non-sinusoidal signals (True-RMS function). Amp-Tip is a small wire guide that is built into the tip of the main clamp meter jaws. It allows for precise measurement of low-current down to the tenth of an amp on small diameter wires, to provide reliable, accurate measurements. VOLTAGE DROP TEST WITH DUAL DISPLAY SCREEN: Dual display allows user to view voltage and current simultaneously to assess voltage drop for current changing from zero to a maximum value. Voltage drop test is required by National Electrical Code (NEC) to ensure normal operation and efficiency. It defines the maximum percentage of the voltage drop between maximum voltage at zero current and minimum voltage at maximum current. This assures that electrical equipment and motors are working within specified voltage to avoid potential damage to electrical components. CORE HVAC FEATURES AND FUNCTIONS: Temperature measurement (with included thermocouple), capacitance for start-up and run capacitors, and DC micro-amps for flame sensors testing.

INCLUDES: • DM-5 Power Quality Analyzer • Flexible 3-Sensor Current Transducer • 1000A Flexible Neutral Current Transducer • Test Leads with Alligator Clips • Data Analysis PC Software • Data Transfer Cable • 2 GB SD Memory Card • Power Adapter • Batteries (AA) • Large Carrying Case • Users Manual FEATURES: • Quick Setup with On-Screen Guide: A step-by-step setup guide helps ensure you capture the right measurements • Real-time remote monitoring on compatible PC and Android devices via Bluetooth communication • Simultaneously measures power, harmonics, waveform, power quality (voltage: 3-channel, current: 4-channel) • Full Analysis with Included Software: Quickly analyze your recorded data to identify potential issues with report generation and data visualization. • Test parameters: voltage, current, active/reactive/apparent power, PF and frequency all on one screen • Power quality events: Swell, Dip, Interruption, transients, Inrush current, and flicker • Automatic recording with memory for up to 1,000 parameters at user defined intervals • Comes complete with measurement accessories, PC software, and large carrying case SPECIFICATIONS: • Wiring connection: 1P2W, 1P3W, 3P3W, 3P4W • Measurements and parameters: Voltage, current, frequency, active power, reactive power, apparent power, active energy, reactive energy, apparent energy, power factor (cos ø), neutral current, demand, harmonics, quality (swell/dip/interruption, transients/overvoltage, inrush current, unbalance rate), capacitance calculation for PF correction unit, flicker • Voltage (rms): Range: 600.0 / 1000 V, Accuracy: ±0.2% + 0.2%f.s.(sine wave, 40 Hz to 70 Hz), Allowable input: 1% to 120% of each range (rms). 200% of each range (peak), Display range: 0.15% to 130 % of each range, Crest factor: 3 or less, Sampling speed of voltage transient: 24 ?s and Input impedance: approx. 1.67 M? • Current (rms): Accuracy: ±0.2% + 0.2%f.s. + accuracy of flex current sensor (sine wave, 40 Hz to 70 Hz), Allowable input: 1% to 110% of each range (rms). 200% of each range (peak), Display range: 0.15% to 130 % of each range, Crest factor: 3 or less and Input impedance: approx. 100 k? • Swell / dip / interruption: Range: same as Voltage (rms), Accuracy: ±1.0% of nominal voltage and Threshold value: In percentage of nominal voltage value • Power and energy: CT-53 flex current sensor (3-ch): max. 6000 kW, CT-500 flex current sensor (1-ch): max. 1000 kW, Active power accuracy: ±0.3% + 0.2%f.s. + accuracy of flex current sensor (PF 1, sine wave, 40 Hz to 70 Hz) Influence of power factor: ±1.0% (PF 0.5, 40 Hz to 70 Hz ), Wh: 0.00000 mWh to 9999.99 TWh, VAh: 0.00000 VAh to 9999.99 TVAh and varh: 0.00000 varh to 9999.99 Tvarh • Power factor:Display range: -1.000 to 0.000 to 1.000 and Accuracy: ±1dgt against each calculated value (for sum: ±3dgt) • Harmonics:Harmonics order (n): 1 to 50th Inter-harmonics order (n): 1 to 50thVolts: 0.0% to 100.0%, accuracy (?3% at 100 V nominal voltage): ±10%,accuracy (<3% at 100 V nominal voltage): ±0.3% of nominal voltage accuracy (1000 V range): ±0.2% + 0.2%f.s, Amps: 0.0% to 100.0%, accuracy (?10% to max. input range): ±10% + flex current sensor accuracy (<10% to max. input range): ±1.0% + flex current sensorWatts: 0.0% to 100.0%, accuracy: ±0.3% + 0.2%f.s. + accuracy of flex current sensor (PF 1, sine wave, 50/60 Hz) THD: 0.0% to 100.0%, Phase angle: 0.0° to ± 180° • Flicker: Displayed items: Pst(1min), Pst, Plt, Max Pst, Max Plt, V, time left, Measurement method: Complied with IEC 61000-4-30 and IEC 61000-4-15 Ed.2 and Accuracy: Pst (max.20): ±10% according to IEC 61000-4-15 • Unbalance: Volts: 0.00% to 100.00%, accuracy: ±0.3% at 50/60 Hz, sine wave (0.00% to 5.00% according to IEC 61000-4-030) and Current: 0.00% to 100.00% • Transient: Approx. 40.96 ksps (every 2.4 ?s), Range: 50 V to 2200 Vdc and Accuracy: ±0.5% at 1000 Vdc • Inrush current: Range: same as Current (rms), Accuracy: ±0.4% + 0.4%f.s. + accuracy of flex current sensor and Threshold value: In percentage of the measurement range • Capacitance: Range: 0.000 nF to 9999 F, 0.000 kvar to 999 kvar The new Amprobe DM-5 Power Quality Analyzer allows you to easily and quickly discover the source and magnitude of power quality issues. Poor power quality is costly – not only can it drive up energy bills with excessive power usage, but equipment failure or damage caused by poor power quality is expensive and time-consuming to diagnose and repair. Productivity and process also suffer with faulty equipment or unscheduled outages. At half the size of previous models, the compact DM-5 brings speed and efficiency to power quality jobs ranging from routine maintenance to in-plant troubleshooting of individual machinery and power distribution panels. Built for use in even one of the largest facilities, the DM-5 is safety tested to meet the world’s most prestigious safety standards and is rated to CAT IV 300 V, CAT III 600 V, CAT II 1000 V. REAL-TIME CHECKS WITH LARGE, FULL-COLOR SCREEN: During and after measurements, the on-board screen displays data graphs and values in full color for easy comparison. Additionally, the Print Screen quick-button makes it simple to save momentary readings for later comparison. WIRELESS CONTROL FOR REMOTE CHECKS AND ADJUSTMENTS: Adjust settings and transfer data remotely by connecting the DM-5 to compatible Bluetooth enabled Windows and Android devices. This provides added convenience and safety, allowing for easy testing modifications even when the main unit is in difficult to access locations. FULL ANALYSIS WITH INCLUDED SOFTWARE: Quickly analyze your recorded data to identify potential issues with report generation and data visualization.

INCLUDES: • AT-6000-R Receiver • AT-6000-T Transmitter • TL-6000 Test Lead and Accessory Kit • CC-6000 Hard Carrying Case • (12) 1.5 V AA (IEC R6) Batteries (not installed) • User Manual FEATURES: • Traces wires in walls, ceilings, floors and corners • Locates breakers and fuses • Pinpoints shorts and opens • High resolution 2.5" TFT LCD color display • Three Transmitter signal modes ?"High Signal" mode for normal circuits, ?"Low Signal" mode for precision tracing in difficult areas, ?"Loop" mode for closed loop de-energized circuits • Four Receiver tracing modes: "Quick Scan" mode allows for quick wire detection at a longer distance, "Precision" mode precisely pinpoints wires or faults located behind walls, floors, or ceilings, "Breaker Identification" mode facilitates quick and easy breaker locating and "Non-Contact Voltage Detection" mode utilizes passive tracing without the Transmitter to verify if a wire is energized • Two automatically selected frequency modes for reliable tracing on energized and de-energized circuits • Compatible with optional Signal Clamp (CT-400) clamp-on attachment and TIC 410A Hot Stick attachment to extend your reach SPECIFICATIONS: • Measurement Category: (Receiver) CAT III 600 V (Transmitter) CAT III 600 V (Signal Clamp) CAT IV 600 V, CAT III 1000 V • Operating voltage: (Receiver & Transmitter) 0 to 600 V AC/DC (Signal Clamp) 0 to 1000 V AC • Operating frequency: (Receiver & Transmitter) Energized: 6.25 kHz, De-Energized: 32.768 kHz (Signal Clamp) Wire tracing: 32.768 kHz and AC current measurement: 45 Hz to 400 Hz • Signal indications: (Receiver) Numeric, bar graph display and audible beep (Transmitter) LEDs and audible beep • Range detection (open air): (Receiver) Tip sensor, (Energized): Max distance via air: up to 20 ft (6.1 m), Pinpointing: approx. 1.97 in (5 cm), Tip sensor (De-energized): Max distance via air: up to 14.7 ft (4.5 m), Pinpointing: approx. 1.97 in (5 cm), NCV detection (40 to 400 Hz): Max. sensitivity: 90 V up to 6.56 ft (2 m) and Min. sensitivity: 600 V up to 0.39 in (1 cm) Amprobe’s newest wire tracer combines a Receiver and powerful Transmitter to locate energized and de-energized wires, breakers, and fuses without having to disconnect any equipment. The Receiver features four tracing modes optimized for a range of applications. Its fully automatic breaker tracing capability saves time and eliminates the confusion of multiple false positives by detecting the highest recorded signal in a breaker or fuse. The Transmitter utilizes two optimized frequencies that allows for a clean and reliable signal. The Signal Clamp can be used in applications where there is no access to bare conductors by enabling the Transmitter to induce a signal into a wire through insulation. Whether you’re a novice user or an expert, the AT-6020 Amprobe Advanced Wire Tracer kit will help you get the job done fast. PACKED WITH TRACING MODES!: The AT-6000 series features 4 tracing modes: “Quick Scan” mode allows for quick wire detection at a longer distance, “Precision” mode precisely pinpoints wires or faults located behind walls, floors, or ceilings, “Breaker Identification” mode facilitates quick and easy breaker locating and, “Non-Contact Voltage Detection” mode utilizes passive tracing without the Transmitter to verify if a wire is energized. MEASURE A VARIETY OF CIRCUITS: Three Transmitter signal modes: “High Signal” mode for normal circuits, “Low Signal” mode for precision tracing in difficult areas and “Loop” mode for closed loop de-energized circuits. SIMPLE AND EASY-TO-USE: This Advanced Wire Tracer Kit is fully equipped with an automatic, simple user interface. Only 2 tracing frequencies for a cleaner, more reliable signal (energized 6 kHz, de-energized 33 kHz).

INCLUDES: • 37XR-A TRMS Digital Multimeter • Test Leads with Threaded Alligator Clips (TL36A) • 9 V Battery (installed) • Magne-Grip Holster with Magnetic Hanging Strap • Spare Fuse • User Manual FEATURES: • Backlight, True-rms with component and logic test • Inductance to 40 H, frequency to 40 MHz, capacitance to 400 ?F, logic to 20 MHz • Input warning tone when test leads are in wrong jack • 10 Amps AC/DC, fully safety fused • Continuity beeper • Min/max, average, relative, peak, and data hold • Auto power off to save battery life • Separate door for easy battery and fuse access • Magne-Grip™ Holster with magnetic hanging strap SPECIFICATIONS: • Autoranging; display: 4-3/4 digit LCD, 10,000 counts with 41-segment analog bar graph • Display Update Rate: 2/sec, nominal • Power Battery: 9 V NEDA 1604, JIS 006P, IEC 6F22 • DC Voltage: 1.000 mV, 10.00 V, 100.0 V, 1000 V • AC Voltage: 1.000 mV, 10.00 V, 100.0 V, 1000 V • DC Current: 100.0 µA, 1.000 µA, 10.00 mA, 100.0 mA, 400.0 mA, 10.00 A • AC Current: 100.0 µA, 1.000 µA, 10.00 mA, 100.0 mA, 400.0 mA, 10.00 A • Resistance: 1000.0 O, 10.000 kO, 100.00 kO, 1000.0 kO, 10.00 MO , 40.00 MO • Continuity: Yes • Diode: Yes • Capacitance: 40.00 nF. 400.0 nF, 4.000 µF, 40.00 µF, 400.0 µF • Frequency: 100.00 Hz, 1.0000 kHz, 10.000 kHz, 100.00 kHz, 1.0000 MHz, 10.000 MHz • Duty cycle: 0.00 % ? 90.0 % • Logic test: Yes • Inductance: 40 H • dBm: -13 dBm ? + 50 dBm The XR Multimeter Series lets you customize features and functions for your electric, electrical, plant maintenance or HVAC applications. HVAC contractors and field service technicians have a choice of the manual ranging 37XR-A with capacitance of the auto ranging, True-RMS 38XR-A offers component and logic test. If you're an engineer, designing or troubleshooting industrial automation and control systems, check out the 38XR-A, a True-RMS multimeter with bright blue backlight and an optical PC interface. VOLTECT NON-CONTACT TECHNOLOGY: The 37XR-A Multimeter features auto and manual ranging for measuring current, voltage, resistance, capacitance, frequency, inductance, duty cycles, logic states, and dBm function. EASY-TO-READ MEASUREMENTS: The Amprobe 37XR-A Digital Multimeter is a feature packed, rugged and reliable multimeter. It displays true-rms measurement on a low-light backlit LCD screen. TRUE-RMS MEASUREMENT: The Amprobe 37XR-A Digital Multimeter offers true-rms measurement along with component and logic testing for troubleshooting electronics at the bench or on the job site.

INCLUDES: • AT-6000-R Receiver • AT-6000-T Transmitter • TL-6000 Test Lead and Accessory Kit • CC-6000 Hard Carrying Case • (12) 1.5 V AA (IEC R6) Batteries (not installed) • User Manual FEATURES: • Traces wires in walls, ceilings, floors and corners • Locates breakers and fuses • Pinpoints shorts and opens • High resolution 2.5" TFT LCD color display • Two automatically selected frequency modes for reliable tracing on energized and de-energized circuits • Compatible with optional TIC 410A Hot Stick attachment to extend your reach • Three Transmitter signal modes • Four Receiver tracing modes SPECIFICATIONS: • Measurement Category (Receiver & Transmitter): CAT III 600 V (Signal Clamp): CAT IV 600 V, CAT III 1000 V • Operating voltage (Receiver & Transmitter):0 to 600 V AC/DC (Signal Clamp): 0 to 1000 V AC • Operating frequency (Receiver & Transmitter): Energized: 6.25 kHz De-Energized: 32.768 kHz (Signal Clamp): Wire tracing: 32.768 kHz AC current measurement: 45 Hz to 400 Hz • Hazardous voltage detection (Transmitter): > 30 V AC/DC • Signal indications (Receiver): Numeric, bar graph display and audible beep (Transmitter): LEDs and audible beep • Response time (Receiver): Tip Sensor (energized/de-energized): 500 MS NCV: 500 MS Battery voltage monitoring: 5 sec (Transmitter): Line voltage monitoring: 1 sec Battery voltage monitoring: 5 sec (Signal Clamp): Instantaneous • Current output of signal (typical): Transmitter: Energized circuit: HI mode: 60 mA RMS, LO mode: 30 mA RMS, De-energized circuit: HI mode: 130 mA RMS, LO mode: 40 mA RMS, Loop mode: 160 mA RMS and Signal Clamp: mA/A for AC current measurement with multimeter • Signal voltage output (nominal)Transmitter: De-energized circuit: LOW: 29 V RMS, 120 Vp-p HIGH: 33V RMS, 140 Vp-p With CT-400: loop model: 31 V RMS, 120 Vp-p Signal Clamp: De-energized circuit: 2.4 V RMS, 24 Vp-p • Range detection (open air) Recevier: Tip sensor (Energized): Max distance via air: up to 20 ft (6.1 m), Pinpointing: approx. 1.97 in (5 cm), Tip sensor (De-energized): Max distance via air: up to 14.7 ft (4.5 m), Pinpointing: approx. 1.97 in (5 cm), NCV detection (40 to 400 Hz): Max. sensitivity: 90 V up to 6.56 ft (2 m) and Min. sensitivity: 600 V up to 0.39 in (1 cm) Amprobe’s newest wire tracer combines a Receiver and powerful Transmitter to locate energized and de-energized wires, breakers, and fuses without having to disconnect any equipment. The Receiver features four tracing modes optimized for a range of applications. Its fully automatic breaker tracing capability saves time and eliminates the confusion of multiple false positives by detecting the highest recorded signal in a breaker or fuse. The Transmitter utilizes two optimized frequencies that allows for a clean and reliable signal. The Signal Clamp can be used in applications where there is no access to bare conductors by enabling the Transmitter to induce a signal into a wire through insulation. Whether you’re a novice user or an expert, the AT-6020 Amprobe Advanced Wire Tracer kit will help you get the job done fast. PACKED WITH TRACING MODES!: The AT-6000 series features 4 tracing modes: “Quick Scan” mode allows for quick wire detection at a longer distance, “Precision” mode precisely pinpoints wires or faults located behind walls, floors, or ceilings, “Breaker Identification” mode facilitates quick and easy breaker locating and, “Non-Contact Voltage Detection” mode utilizes passive tracing without the Transmitter to verify if a wire is energized. MEASURE A VARIETY OF CIRCUITS: Three Transmitter signal modes: “High Signal” mode for normal circuits, “Low Signal” mode for precision tracing in difficult areas and “Loop” mode for closed loop de-energized circuits. SIMPLE AND EASY-TO-USE: This Advanced Wire Tracer Kit is fully equipped with an automatic, simple user interface. Only 2 tracing frequencies for a cleaner, more reliable signal (energized 6 kHz, de-energized 33 kHz).

INCLUDES: • (1) Infrared Camera • (3) AA Batteries • (1) User Manual FEATURES: • Infrared heat map image blending at 0%, 25%, 50%, 75%, and 100%, a Fluke patented technology that can be adjusted for easier interpretation between infrared and visual images • Center-point temperature measurement with a marker that indicates the center of the infrared thermometer measurement spot, making it easy to determine the surface temperature of the desIRed target. • Focus free lens that automatically focuses based on depth of field, providing a sharp image without having to manually adjust the lens. SPECIFICATIONS: • Unit Weight (KG): 0.43 • Unit Height (CM): 3 • Unit Length (CM): 18 • Unit Width (CM): 8 The Amprobe IRC-110 thermal camera is rugged with point-and-shoot functionality to give you a visual heat map combined with a sharp photographic image for quick and accurate identification of temperature related issues. Troubleshoot electrical connections, motors, HVAC and electrical, and insulation leaks around buildings to identify potential energy savings.

INCLUDES: • Amprobe NCV-1030 Non-Contact Voltage Tester • 2 x 1.5 V Batteries (installed) • User Manual FEATURES: • Detects the presence of AC voltage in cables, circuit breakers, wall sockets, junction boxes, fuses, extension cords and more • Tests voltage through wire insulation • Identifies cable breaks in wires, cords and lightning systems connected in series • Identifies polarity (line vs. neutral) of receptacles and cables • Safely tests voltage in non-contact way • Safety CAT IV 1000 V rated for wide range of applications • IP65 rated (water and dust resistant) for indoor and outdoor use SPECIFICATIONS: • Operating Voltage Range: 12-50 Vac, 50-1000 Vac, 50-400 Hz • Voltage Indication: Bright red LED and buzzer • Voltage Detection: Illuminates at approximately 10 mm (0.39 in) distance from a wire carrying 120 Vac • Temperature Range: 32 °F to 104 °F (0 °C to 40 °C), ? 80% RH • Storage Conditions: 14 °F to 104 °F (-10 °C to 40 °C), ? 85% RH • Operating Altitude: ? 6561 ft (2000 m) • Power Supply: 2 1.5 V LR03 AAA batteries • Duty Cycle: Continuous • Current Consumption: Approximately 80 mA • Dimensions (L x W x H): 156.2 x 23.5 x 27.5 mm (6.14 x 0.92 x 1.08 in) • Weight (with batteries installed): Approx. 60 g (0.13 lb) The Amprobe NCV-1000 Non-Contact Voltage (NCV) series tester provides maximum safety and convenience for detecting AC voltage without interrupting electrical systems. Designed to conveniently fit in your shirt pocket, the NCV-1000 series tester performs in indoor and outdoor settings. Safety tested to the highest category measurement, CAT IV 1000 V, as well as IP65 water and dust resistant, the NCV-1000 series is fit for the toughest industrial applications. WIDE RANGE OF MEASUREMENTS: Detect the presence of AC voltage in cables, circuit breakers, wall sockets, junction boxes, fuses, extension cords and tests voltage through wire insulation. PACKED WITH FEATURES!: Identify cable breaks in wires, cords and lightning systems connected in a series. Identify polarity (line vs. neutral) of receptacles and cables. SIMPLE AND EASY-TO-USE: The Amprobe NCV-1030 features a built-in work light to test voltage in dark areas.

INCLUDES: • Amprobe NCV-1040 Non-Contact Voltage Tester • 2 x 1.5 V Batteries (installed) • User Manual FEATURES: • Detects the presence of AC voltage in cables, circuit breakers, wall sockets, junction boxes, fuses, extension cords and more • Tests voltage through wire insulation • Identifies cable breaks in wires, cords and lightning systems connected in series • Identifies polarity (line vs. neutral) of receptacles and cables • Safely tests voltage in non-contact way • Safety CAT IV 1000 V rated for wide range of applications • IP65 rated (water and dust resistant) for indoor and outdoor use • Magnetic solenoid detection to diagnose electromagnets and relays SPECIFICATIONS: • Operating Voltage Range: 12-50 Vac, 50-1000 Vac, 50-400 Hz • Voltage Indication: Bright red LED and buzzer • Voltage Detection: Illuminates at approximately 10 mm (0.39 in) distance from a wire carrying 120 Vac • Magnetic Field: Indication Yellow LED • Detection of Magnetic Field: > 2.5 mT • Temperature Range: 32 °F to 104 °F (0 °C to 40 °C), ? 80% RH • Storage Conditions: 14 °F to 104 °F (-10 °C to 40 °C), ? 85% RH • Operating Altitude: ? 6561 ft (2000 m) • Power Supply: 2 1.5 V LR03 AAA batteries • Duty Cycle: Continuous • Current Consumption: Approximately 80 mA • Dimensions (L x W x H): 156.2 x 23.5 x 27.5 mm (6.14 x 0.92 x 1.08 in) • Weight (with batteries installed): Approx. 62 g (0.136 lb) The Amprobe NCV-1000 Non-Contact Voltage (NCV) series tester provides maximum safety and convenience for detecting AC voltage without interrupting electrical systems. Designed to conveniently fit in your shirt pocket, the NCV-1000 series tester performs in indoor and outdoor settings. Safety tested to the highest category measurement, CAT IV 1000 V, as well as IP65 water and dust resistant, the NCV-1000 series is fit for the toughest industrial applications. WIDE RANGE OF MEASUREMENTS: Detect the presence of AC voltage in cables, circuit breakers, wall sockets, junction boxes, fuses, extension cords and tests voltage through wire insulation. PACKED WITH FEATURES!: Identify cable breaks in wires, cords and lightning systems connected in a series. Identify polarity (line vs. neutral) of receptacles and cables. MAGNETIC SOLENOID DETECTION: The Amprobe NCV-1040 Non-Contact Voltage Tester includes magnetic solenoid detection to diagnose electromagnets and relays.

INCLUDES: • (1) Advanced Wire Tracer • (1) AT-6010-R Receiver • (12) Batteries • (1) Soft Carrying Case • (1) User Manual FEATURES: • Large LCD Receiver screen with two digit readout, bar graph and sound to easily determine wire location • Rated CAT III 600 V for work directly on an Energized circuits without taking equipment offline • Simple one button Transmitter operation • Compatible with the CT-400 Signal Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors SPECIFICATIONS: • Measurement Category: CAT III 600 V • Transmitter Operating Voltage: 0 to 600 V AC/DC • Receiver Display: B&W 2.5" LCD With the AT-6010 Advanced Wire Tracer, it’s never been easier and safer to locate Energized and De-energized wires, breakers and fuses. When the Transmitter is connected to the circuit, the Receiver easily detects the signal in the wires or cables behind walls, ceilings and floors. The Transmitter works on Energized and De-energized circuits up to 600 V AC/DC in Category I through Category III electrical environments, allowing for work directly on an energized circuit without the need to take equipment offline. The Transmitter also features high signal mode for general tracing and a loop mode designed specifically for locating shorts, as well as two optimal tracing frequencies that are automatically activated based on the detected voltage. The complete AT-6010 kit features test leads and accessories International accessory kit for use outside North America.