Gardner Bender JLP10 100' Non-Conductive Replacement Fish Tape (Coil Only)
Regular price
$85.60
/
Gardner Bender JLP10 Specifications:
• Length: 100'
• Tape Diameter: 3/16"
Gardner Bender JLP10 Features:
• Non-conductive fish tape - light and flexible.
• Designed for use in conduit with existing wires or cables.
• Glides through 1/2" to 4" conduit.
• High-strength nylon tape tested at 300 lbs. average tensile strength.
• 6" spiral wound metal leader with pulling eyelet included (attached).
• For use with NYD-100 fish tape housing (sold separately)
Gardner Bender JLP5 Non-conductive Replacement Tape for NYD-100 Fish Tape, Nylo-Flex, 50' x 3/16"
Regular price
$49.71
/
INCLUDES:
• (1) Fish Tape
FEATURES:
• Designed for use in conduit with existing wires or cables
• Glides through 1? 2" to 4" conduit
• High-strength nylon tape tested at 300 lbs average tensile strength
• Tape diameter is 3? 16"
SPECIFICATIONS:
• Non-Conductive
• Glides through 1? 2" to 4" conduit
• 300 lbs average tensile strength
• 50' Long X 3/16" Diameter
Non-conductive fish tape - light and flexible.
INCLUDES:
• 1105A* 12' Valve Assembly with UG12 hose only
• 1215 Seal-off for 1/2" - 1" conduit with 2' hose
• 1142 Angle Adapter (for 1215 Seal-off)
• 1216 Seal-off for 1-1/4" - 2-1/2" conduit with 2' hose
• 1206 Seal-off for 1-1/2" - 6" conduit
• LP2150 (10) 150' Line Pkgs for 1/2" conduit
• LP3200 (5) 200' Line Pkgs for 3/4" conduit
• LP3300 (5) 300' Line Pkgs for 3/4" conduit
• LP4300 (5) 300' Line Pkgs for 1" conduit
• LP2206T (3) 400' Line Pkgs for 1-1/4" or larger conduit
• LP2207T (3) 800' Line Pkgs for 1-1/4" or larger conduit
• LP2208T (3) 600' Line Pkgs for 1-1/4" or larger conduit
• FC1 Foam Line Carrier for 1/2" conduit
• FC2 Foam Line Carrier for 3/4" conduit
• FC3 Foam Line Carrier for 1" conduit
• FC4 Foam Line Carrier for 1-1/4" conduit
• FC5 Foam Line Carrier for 1-1/2" conduit
• FC6 Foam Line Carrier for 2" conduit
• FC7 Foam Line Carrier for 2-1/2" conduit
• FC8 Foam Line Carrier for 3" conduit
• FC9 Foam Line Carrier for 3-1/2" conduit
• FC10 Foam Line Carrier for 4" conduit
• FC11 Foam Line Carrier for 5" conduit
• FC12 Foam Line Carrier for 6" conduit
FEATURES:
• Quick, easy set up
• Metered operating valve controls CO2 volume to minimize waste and maximize safety
• Locking pull ring prevents accidental discharge
SPECIFICATIONS:
• Specifications: 840 psi @70 F
• 1" tank thread
Power House Conduit Fishing Systems. Completely self-contained with no electrical power source required. Use 50 lb. cylinder as source for refilling smaller cylinders (requires RV5 refill connector).
INCLUDES:
• 1105A* 12' Valve Assembly with UG12 hose only
• 1215 Seal-off for 1/ 2" - 1" conduit with 2' hose
• 1142 Angle Adapter (for 1215 Seal-off)
• 1216 Seal-off for 1-1/ 4" - 2-1/ 2" conduit with 2' hose
• 1206 Seal-off for 1-1/ 2" - 6" conduit
• LP2150 (10) 150' Line Pkgs for 1/ 2" conduit
• LP3200 (5) 200' Line Pkgs for 3/ 4" conduit
• LP3300 (5) 300' Line Pkgs for 3/ 4" conduit
• LP4300 (5) 300' Line Pkgs for 1" conduit
• LP2206T (3) 400' Line Pkgs for 1-1/ 4" or larger conduit
• LP2207T (3) 800' Line Pkgs for 1-1/4" or larger conduit
• LP2208T (3) 600' Line Pkgs for 1-1/4" or larger conduit
• FC1 Foam Line Carrier for 1/ 2" conduit
• FC2 Foam Line Carrier for 3/ 4" conduit
• FC3 Foam Line Carrier for 1" conduit
• FC4 Foam Line Carrier for 1-1/ 4" conduit
• FC5 Foam Line Carrier for 1-1/ 2" conduit
• FC6 Foam Line Carrier for 2" conduit
• FC7 Foam Line Carrier for 2-1/ 2" conduit
• FC8 Foam Line Carrier for 3" conduit
• FC9 Foam Line Carrier for 3-1/ 2" conduit
• FC10 Foam Line Carrier for 4" conduit
• FC11 Foam Line Carrier for 5" conduit
• FC12 Foam Line Carrier for 6" conduit
FEATURES:
• Quick, easy set up
• Metered operating valve controls CO2 volume to minimize waste and maximize safety
• Locking pull ring prevents accidental discharge
SPECIFICATIONS:
• Specifications: 840 psi @70 F
• 1" tank thread
Power House Conduit Fishing Systems. Completely self-contained with no electrical power source required. 5 lb. cylinder can be refilled from larger cylinder (requires RV5 refill connector).
Gardner Bender JO25A Powr-Pak CO2 System without 1103N
Regular price
$884.30
/
INCLUDES:
• (1) Powr-Pak CO2 System without 1103N
FEATURES:
• For 1/2" to 2-1/2" conduit
• 5 lb Cylinder Can Be Refilled from Larger Cylinder Using #RV5 Refill Connector
• Metered Operating Valve Controls Volume, Preventing Waste
• Lightweight, Portable System Requires No Electrical Power
• Locking Pull Ring Prevents Accidental Discharge
• Specifications: 840 Psi @ 70 °F
• 3/4" NGA Tank Thread
SPECIFICATIONS:
• Handheld: Yes
• Blowing Method: CO2 Cylinder
• Series: Powr-Pak Portable System
• Item Category: Wire Pulling
• Each in Package Height (in): 10.5
• Each in Package Width (in): 10.5
• Each in Package Length/Depth (in): 19.5
• Each in Package Weight (oz): 295.1
Powr-Pak I™ 5-lb Portable System. For 1/2" to 2-1/2" conduit. Lightweight, portable system requires no electrical power. Metered operating valve controls volume, preventing waste. 5 lb cylinder can be refilled from larger cylinder. Locking pull ring prevents accidental discharge. 3/4" NGA tank thread. specifications: 840 psi @ 70°F. Product NOT usable for conduit runs that have set-screw fittings that have not been sealed.
Show 12 products per page Show 24 products per page Show 48 products per page
Sort by relevance Sort by price, low to high Sort by price, high to low Sort by popularity
Gardner Bender KC3540 Slug-Out Knockout Converter - 3-1/2" and 4" (8.89 and 10.16 cm)
Regular price
$65.68
/
INCLUDES:
• (1) Converter
FEATURES:
• For use with 3-1/2" to 6" punches and dies
• Eliminates the need for spacers
• Helps to center the hole
• Requires 1.5 inch guide hole
SPECIFICATIONS:
• For use with 3-1/2" to 6" punches and dies
• Requires 1.5 inch guide hole
Use the Gardner Bender KC3540 Knockout Converter whenever you need to create larger punch sizes (3.5 to 6 inch). Designed for use with the GB KOH14A Slug-Out Hydraulic Knockout Set and compatible with most 3.5" punch and die sets the converter eliminates the need for spaces and helps to center the hole. Thread the KC3540 converter into the punch from the inside until seated making sure the die counter bore is positioned over the boss projecting from the port end of the cylinder. The converter requires a 1.5 Inch diameter or larger guide hole (use 1-1/2" punch and die) to be drilled prior to use. It is important to install the converter on the inside of the punch as damage to the pull rod would result from incorrect installation of the converter on the outside of the punch. Once you've placed the pull rod into the guide hole. Install the punch on the pull rod and turn until the converter is into the guide hole.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 1.5 Inch pipe or conduit
• Actual hole diameter 1.937 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 1.5 Inch pipe or conduit
• Actual hole diameter 1.937 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 1.5 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 2 Inch pipe or conduit
• Actual hole diameter 2.43 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 2 Inch pipe or conduit
• Actual hole diameter 2.43 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 2 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 2.5 Inch pipe or conduit
• Actual hole diameter 2.915 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 2.5 Inch pipe or conduit
• Actual hole diameter 2.915 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 2.5 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 3 Inch pipe or conduit
• Actual hole diameter 3.542 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 3 Inch pipe or conduit
• Actual hole diameter 3.542 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 3 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 3.5 Inch pipe or conduit
• Actual hole diameter 4.043 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 3.5 Inch pipe or conduit
• Actual hole diameter 4.043 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 3.5 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 4 Inch pipe or conduit
• Actual hole diameter 4.545 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 4 Inch pipe or conduit
• Actual hole diameter 4.545 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 4 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 1/2 Inch pipe or conduit
• Actual hole diameter 0.873 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 1/2 Inch pipe or conduit
• Actual hole diameter 0.873 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 1/2 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
INCLUDES:
• (1) Knockout Die
FEATURES:
• When used with GB 4-point punches the slug falls free from the die without the need for tapping or prying
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 3/4 Inch pipe or conduit
• Actual hole diameter 1.086 inches
SPECIFICATIONS:
• For 10-gauge mild steel and 12-gauge stainless steel
• Punches hole designed for 3/4 Inch pipe or conduit
• Actual hole diameter 1.086 inches
Gardner Bender dies are interchangeable, in any combination, with most brands of knockouts. Constructed from black oxide coated, hardened and tempered chrome-moly steel. Use this 3/4 Inch Die in combination with GB 4-point slug-outs to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
Show 12 products per page Show 24 products per page Show 48 products per page
Sort by relevance Sort by price, low to high Sort by price, high to low Sort by popularity
Gardner Bender KOH2540 Slug-Out Mechanical Knockout Set, 2.5" - 4" Punches and Dies in Metal Case
Regular price
$939.56
/
INCLUDES:
• (4) Punches - 1 Each: 2.5", 3", 3.5" and 4"
• (4) Dies - 1 Each: 2.5", 3", 3.5" and 4"
• (1) Metal Storage Case
FEATURES:
• Four-point punch design allows slug to fall free from the die without splitting, tapping or prying
• Interchangeable with most tool brands
• Punches 10 gauge mild and 12 gauge stainless steel
• Durable metal storage case
• Kit includes punches and dies to punch holes designed for 2.5 inch to 4 inch pipe or conduit with actual hole diameters of 2.915 inches to 4.545 inches
SPECIFICATIONS:
• Punches 10 gauge mild and 12 gauge stainless steel
Gardner Bender four-point knockout punches and dies are designed to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Punches and dies are interchangeable, in any combination, with most brands of knockouts. This assortment kit includes one Punch and Die pair in each size: 2.5", 3", 3.5" and 4" for a total of 8 pieces (4 Punches and 4 Dies) in a durable metal flip-lock storage case. Additional kits and individual punch and die sizes are available from GB to specifically permit fast and easy installation of electrical conduit and pipe in all commonly available increments.
Gardner Bender KOM200 Slug-Out Mechanical Knockout Set for 2" (5.08 cm) Conduit
Regular price
$111.08
/
INCLUDES:
• (1) Punch
• (1) Die
• (1) Drive Screw
FEATURES:
• Four-point punch design allows slug to fall free from the die without splitting, tapping or prying
• Interchangeable with most tool brands
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 2 Inch pipe or conduit
• Actual hole diameter 2.413 inches
• Set includes Punch, Die and Drive Screw
SPECIFICATIONS:
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 2 Inch pipe or conduit
• Actual hole diameter 2.413 inches
Gardner Bender four-point knockout punches and dies are designed to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Punches and dies are interchangeable, in any combination, with most brands of knockouts. This kit includes punch, die and drive screw to punch a hole diameter sufficient for 2 inch diameter pipe/conduit; actual hole diameter is 2.915 inches. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
Gardner Bender KOM250 Slug-Out Mechanical Knockout Set for 2-1/2" (6.35 cm) Conduit
Regular price
$210.79
/
INCLUDES:
• (1) Punch
• (1) Die
• (1) Drive Screw
FEATURES:
• Four-point punch design allows slug to fall free from the die without splitting, tapping or prying
• Interchangeable with most tool brands
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 2.5 Inch pipe or conduit
• Actual hole diameter 2.915 inches
• Set includes Punch, Die and Drive Screw
SPECIFICATIONS:
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 2.5 Inch pipe or conduit
• Actual hole diameter 2.915 inches
Gardner Bender four-point knockout punches and dies are designed to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Punches and dies are interchangeable, in any combination, with most brands of knockouts. This kit includes punch, die and drive screw to punch a hole diameter sufficient for 2.5 inch diameter pipe/conduit; actual hole diameter is 3.542 inches. Additional sizes available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
Gardner Bender KOM300 Slug-Out Mechanical Knockout Set for 3" (7.62 cm) Conduit
Regular price
$248.13
/
INCLUDES:
• (1) Punch
• (1) Die
• (1) Drive Screw
• (1) Drive Nut
FEATURES:
• Four-point punch design allows slug to fall free from the die without splitting, tapping or prying
• Interchangeable with most tool brands
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 3 Inch pipe or conduit
• Actual hole diameter 3.542 inches
• Set includes Punch, Die, Drive Screw and Drive Nut
SPECIFICATIONS:
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 3 Inch pipe or conduit
• Actual hole diameter 3.542 inches
Gardner Bender four-point knockout punches and dies are designed to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Punches and dies are interchangeable, in any combination, with most brands of knockouts. This kit includes punch, die, drive screw and drive nut to punch a whole diameter sufficient for 3 inch conduit; actual hole diameter is of 3.542 inches. Additional sizes are available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
Gardner Bender KOM400 Slug-Out Mechanical Knockout Set for 4" (10.16 cm) Conduit
Regular price
$560.77
/
INCLUDES:
• (1) Punch
• (1) Die
• (1) Drive Screw
• (1) Drive Nut
FEATURES:
• Four-point punch design allows slug to fall free from the die without splitting, tapping or prying
• Interchangeable with most tool brands
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 4 Inch pipe or conduit
• Actual hole diameter 4.545 inches
• Set includes Punch, Die, Drive Screw and Drive Nut
SPECIFICATIONS:
• Punches 10 gauge mild and 12 gauge stainless steel
• Punches hole designed for 4 Inch pipe or conduit
• Actual hole diameter 4.545 inches
Gardner Bender four-point knockout punches and dies are designed to punch clean, round holes through 10-gauge mild steel, 12-gauge stainless steel or other soft metals up to .135 inches in thickness. Punches and dies are interchangeable, in any combination, with most brands of knockouts. This kit includes punch, die, drive screw and drive nut to punch a hole diameter sufficient for 4 inch pipe/conduit; actual hole diameter is of 4.545 inches. Additional sizes are available to specifically permit fast and easy installation of electrical conduit and pipe of nominal sizes 1/2" through 4", in all commonly available increments.
Gardner Bender KOM520A Mechanical Driver with Case, 1/2" To 2" Knock Outs, Adapter & Draw Stud
Regular price
$1,230.83
/
INCLUDES:
• Mechanical Driver
• Adapter
• Case
• Draw Studs
• 1/2 - 2 knockout set and step bit
FEATURES:
• All Metal Construction - Provides maximum durability in conditions
• Tactile grip - Allows for better control when in use
• Dual Drive - Allows unit to be driven from both sides and any angle
• Universal draw stud design - works with most competitive draw studs to provide maximum jobsite versatility
SPECIFICATIONS:
• Max. Capacity Mild Steel (Ga.): 10ga
• Capacity: 1/2" - 4"
Slug-Out Knockout Mechanical Driver. Turn your ordinary everyday drill into a powerful knockout driver. You win - with the versatile dual drive, durable all metal construction and powerful gear design. Save time, hassle and money with Gardner Bender.
Gardner Bender KOM540A Mechanical Driver with Case, 1/2" To 4" Knock Outs, Adapter & Draw Stud
Regular price
$1,761.21
/
INCLUDES:
• Mechanical Driver
• Adapter
• Case
• Draw Studs
• 1/2 - 4 knockout set and step bit
FEATURES:
• All Metal Construction - Provides maximum durability in conditions
• Tactile grip - Allows for better control when in use
• Dual Drive - Allows unit to be driven from both sides and any angle
• Universal draw stud design - works with most competitive draw studs to provide maximum jobsite versatility
SPECIFICATIONS:
• Max. Capacity Mild Steel (Ga.): 10ga
• Capacity: 1/2" - 4"
Slug-Out Knockout Mechanical Driver. Turn your ordinary everyday drill into a powerful knockout driver. You win - with the versatile dual drive, durable all metal construction and powerful gear design. Save time, hassle and money with Gardner Bender.
