Dremel 482 Specifications:
• Inside Diameter: 1/16″, 1,6 mm
• Part Number: 482
• Color Code: Brown
• Item Description: Collet
Dremel 482 Features:
• The collet features small identification rings around its shank. These rings correspond with the size of the collet: 0 rings = 1/8", 3 rings = 3/32", 2 rings = 1/16", 1 ring = 1/32"
• Collets are compatible with 225 Flex-Shaft attachment.
• For use with all rotary tools except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280.
A slim, aluminum tube that provides the optimal grip for holding a bit in a Dremel rotary tool.
Dremel 483 Specifications:
• Inside Diameter: 1/32″, 0,8 mm
• Part Number: 483
• Color Code: Brown
• Item Description: Collet
Dremel 483 Features:
• The collet features small identification rings around its shank. These rings correspond with the size of the collet: 0 rings = 1/8", 3 rings = 3/32", 2 rings = 1/16", 1 ring = 1/32"
• Collets are compatible with 225 Flex-Shaft attachment.
• For use with all rotary tools except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280.
A slim, aluminum tube that provides the optimal grip for holding a bit in a Dremel rotary tool.
Dremel 500 Specifications:
• Bit Diameter: 1"(25.4 mm)
• Color Code: Green
• Shank Diameter: 1/8"(3.2 mm)
• Model Number: 500
Dremel 500 Features:
• Ideal for sharpening, deburring and general purpose grinding on most materials including stainless steel. Works best for cleaning and rust removal, as well as light polishing.
• For best results, insert the accessory bit all the way into the tool and then back it out slightly before tightening down. This provides plenty of shank for the collet or chuck to hold onto the bit.
Dremel 502 Specifications:
• 80 Grit
• 3/8" diameter
Dremel 502 Features:
• As the flapwheel wears down new abrasive is continuously exposed preventing clogging
• Provides uniform finishing throughout the life of the flapwheel
Dremel 504 Specifications:
• 80 Grit
• 3/16" diameter
Dremel 504 Features:
• As the flapwheel wears down new abrasive is continuously exposed preventing clogging
• Provides uniform finishing throughout the life of the flapwheel
Dremel 511E Specifications:
• Dark brown buff 180 Grit
• Light brown buff 280 Grit
• 1" Diameter
Dremel 511E Features:
• Ideal for cleaning and light sanding
• Works effectively on metal, glass, wood, aluminum and plastics
• Features the EZ lock design for use with any Dremel rotary tool
• Can be used for sanding, removal of rust, paint and lacquer, light deburring on metals and plastics, cleaning solder connections, and creating textured patterns on woodworking projects
• For use with the EZ402 EZ-Lock Mandrel or standard 402 Mandrel (both sold separately)
Dremel 512E Abrasive Buffs (320 grit) EZ Lock compatible
Regular price
$3.97
/
INCLUDES:
• (2) Finishing Abrasive Buffs
FEATURES:
• Compatible with both EZ402 EZ Lock Mandrel and Standard 402 Mandrel
• First patented system of its kind
• Light sanding and tarnish removal - also great for car detailing and restoring door & window hardware
• Compatible with all Dremel rotary tools
SPECIFICATIONS:
• RPM Limit: 15,000
Great for cleaning and light sanding. Use on metal, glass, wood, aluminum and plastics. The 512E fine-grit buff is ideal for removing tarnish from brass.
Dremel 516 Specifications:
• Bit Diameter: 1/2″ (12.7 mm)
• Color Code: Green
• Shank Diameter: 1/8″ (3.2 mm)
• Model Number: 516
Dremel 516 Features:
• Ideal for sharpening, deburring and general purpose grinding on harder materials including stone, glass, ceramic, porcelain, gemstones and non-ferrous metals. Specially designed for working with conic and flat surfaces.
• Use a sanding band or small piece of sandpaper to clean the surface of the abrasive point and restore its original shape.
• Can be used for paint and rust removal without removing any of the base metal.
• For best results, insert the accessory bit all the way into the tool and then back it out slightly before tightening down. This provides plenty of shank for the collet or chuck to hold onto the bit.
Dremel 520 Specifications:
• Tip Size: 1/2" (12.7 mm)
• Shank: 1/8" (3.2 mm)
• Color Code: Yellow
Dremel 520 Features:
• Designed for light stock removal and high luster polishing
• Works on a variety of surfaces including steel, aluminum, brass, silver, hard plastics, gold and other metals
• A cylindrical polishing accessory impregnated with silicon carbide abrasive and a cooling lubricant that eliminates the need for polishing compound
INCLUDES:
• 2 Bits
FEATURES:
• Designed for light stock removal and high luster polishing
• Works on a variety of surfaces including steel, aluminum, brass, silver, hard plastics, gold and other metals
• Impregnated with silicone abrasive and lubricant
• Eliminates the need for polishing compound
SPECIFICATIONS:
• Material: Silicone Carbide Abrasive
A polishing wheel for your rotary tool that has the polishing compound inside. The 520-02 polishing wheel is impregnated with a silicon carbide abrasive and lubricant, eliminating the need for polishing compound. Easy to use and less messy, the 520-02 is perfect for high-luster polishing. Pack includes two polishing wheel accessories.
Dremel 530 Specifications:
• Brush Diameter: 3/4" (19.1 mm)
• Shank Diameter: 1/8" (3.2 mm)
• Color Code: Yellow
Dremel 530 Features:
• Ideal for cleaning, deburring and surface-finishing items made from stainless steel, aluminum, silver, pewter or other white metals.
• It is very effective on flat surfaces and in hard-to-reach places, such as slots.
• No "after rust" when used on corrosive resistant materials like pewter, aluminum and stainless steel
• Note: Do NOT run in excess of 15,000 RPM
Dremel 532 Specifications:
• Bit Diameter: 1/8″ (3.2 mm)
• Color Code: Yellow
• Shank Diameter 1/8″ (3.2 mm)
• Model Number: 532
Dremel 532 Features:
• Ideal for cleaning, deburring and surface-finishing items made from stainless steel, aluminum, silver, pewter or other white metals. It is very effective on flat surfaces and in hard-to-reach places, such as slots.
• Stainless steel wire bristles
• Keep a light touch, letting the tips of the brush do the work. Too much pressure can break the wire bristles.
• Before using on a material, allow the tool with brush to run at operating speed for at least one minute to discharge any loose wire bristles. Make sure no one stands in front of or in line with the brush.
• Do not use stainless steel brushes in areas where carbon steel particles may come in contact with the brush (such as steel workbenches). This prevents rust and contamination.
• For the same reason, always store stainless steel brushes apart from carbon steel brushes.
• Do not run in excess of 15,000 rpm. Therefore, do not use with a Single-Speed MultiPro Rotary Tool or a Heavy-Duty Flex-Shaft Tool unless you use the #221 Foot Speed Control(sold separately).
Dremel 535 Specifications:
• 3/4" brush diameter
• 15000 RPM Max operating speed
Dremel 535 Features:
• These are non-sparking and softer than steel
• They will not scratch soft metals like gold, copper or brass
INCLUDES:
• (2) Brass Brushes
FEATURES:
• Ideal for cleaning and surface-finishing items made from gold, bronze, copper or brass
• Use a brass brush to create a soft, satin or matte finish
• Very effective on flat surfaces and in hard-to-reach areas like slots (brass wire is non-sparking and softer than steel)
• Very effective on flat surfaces and in hard-to-reach areas like slots
SPECIFICATIONS:
• Material: Brass
Wheel tip for general purpose use. Non-sparking and softer than steel. Will not scratch soft metals like gold, copper, brass. Pack includes two brass brush accessories.
INCLUDES:
• (2) Brass Brushes
FEATURES:
• Ideal for cleaning and surface-finishing items made from gold, bronze, copper or brass
• Use a brass brush to create a soft, satin or matte finish
• Very effective on flat surfaces and in hard-to-reach areas like slots (brass wire is non-sparking and softer than steel)
• Great for cleaning
SPECIFICATIONS:
• Weight: .03 lb
• Overall Length: 1.75"
• Bit Diameter Inch: 1/8"
Wheel tip for general purpose use. Non-sparking and softer than steel. Will not scratch soft metals like gold, copper, brass. Pack includes two brass brush accessories.
Dremel 538 Specifications:
• Tip Size: 1" (25.4 mm)
• Shank Size: 1/8" (3.2 mm)
• Color Code: Yellow
• Model Number: 538
Dremel 538 Features:
• Extra-thick nylon bristles are coated with an abrasive grit for material removal on the toughest jobs
• Use for de-burring metal or wood and for removing rust and paint.
• For best results, insert the accessory bit all the way into the tool and then back it out slightly before tightening down
• This provides plenty of shank for the collet or chuck to hold on to
• Oscillate the tool back and forth until the desired finish is obtained
• Note: Do NOT run brush in excess of 20,000 RPM.
INCLUDES:
• (1) Diamond Wheel
FEATURES:
• Ideal for cutting, sawing, carving, sharpening and filing hard materials-including marble concrete, brick, porcelain, ceramics, epoxy and hard woods.
• Wheel is completely coated with fine diamond particles for working with hard materials.
• Designed to last and not lose its shape or break, it provides smooth, fine cuts
SPECIFICATIONS:
• Bit Diameter: 7/8" (22.2 mm)
• Shank Diameter: 1/8" (3.2mm)
• Thickness: .023" (0.6mm)
The 545 Diamond Wheel is completely coated with fine diamond particles for working with hard materials. Designed to be long lasting and not lose its shape or break, it provides smooth, fine cuts. Great for cutting, sawing and carving of hard materials, such as marble, concrete, brick, porcelain, ceramics, hard epoxy and soft and hard wood.
Dremel 560 Specifications:
• Tip Size: 1/8" (3.2 mm)
• Shank Size: 1/8" (3.2 mm)
• Color Code: Red
• Max Run Speed 30,000 RPM
Dremel 560 Features:
• A high-speed cutter with a 1/8" steel shank. Ideal for cutting drywall for electrical boxes, air vents and other wall features
• For use in all Dremel rotary tools
Dremel 561 Specifications:
• Bit Diameter: 1/8" (3.2 mm)
• Shank Diameter: 1/8" (3.2 mm)
• Color Code: Red
• 30000 Max RPM Speed
Dremel 561 Features:
• Ideal for cutting wood, plastic, fiberglass, drywall, laminate, aluminum and vinyl siding
• Start at a 45-degree angle when cutting into a piece of material
